|
 |
 |
 |
 |
 |
 |
 |
| Information | |||
INJECTION MOLD P4 7 Compression MoldingCompression molding is the most common method by which thermosetting plastics are molded. In this method the plastic, in the form of powder, pellet, or disc, is dried by heating and then further heated to near the curing temperature; this heated charge is loaded directly into the mold cavity. The temperature of the mold cavity is held at 1508C�8C, depending on the material. The mold is then partially closed, and the plastic, which is liquefied by the heat and the exerted pressure, flows into the recess of the mold. At this stage the mold is fully closed, and the flow and cure of the plastic are complete. Finally, the mold is opened, and the completely cured molded part is ejected. Compression-molding equipment consists of a matched mold, a means of heating the plastic and the mold, and some method of exerting force on the mold halves. For severe molding conditions molds are usually made of various grades of tool steel. Most are polished to improve material flow and overall part quality. Brass, mild steel, or plastics are used as mold materials for less severe molding conditions or short-run products. In compression molding a pressure of 2,250 psi (158 kg/cm2)�00 psi (211 kg/cm2) is suitable for phenolic materials. The lower pressure is adequate only for an easy-flow materials and a simple uncomplicated shallow molded shape. For a medium-flow material and where there are average-sized recesses, cores, shapes, and pins in the molding cavity, a pressure of 3,000 psi (211 kg/cm2) or above is required. For molding urea and melamine materials, pressures of approximately one and one-half times that needed for phenolic material are necessary. The time required to harden thermosetting materials is commonly referred to as the cure time. Depending on the type of molding material, preheating temperature, and the thickness of the molded article, the cure time may range from seconds to several minutes. In compression molding of thermosets the mold remains hot throughout the entire cycle; as soon as a molded part is ejected, a new charge of molding powder can be introduced. On the other hand, unlike thermosets, thermoplastics must be cooled to harden. So before a molded part is ejected, the entire mold must be cooled, and as a result, the process of compression molding is quite slow with thermoplastics. Compression molding is thus commonly used for thermosetting plastics such as phenolics, urea, melamine, an alkyds; it is not ordinarily used for thermoplastics. However, in special cases, such as when extreme accuracy is needed, thermoplastics are also compression molded. One example is the phonograph records of vinyl and styrene thermoplastics; extreme accuracy is needed for proper sound reproduction. Compression molding is ideal for such products as electrical switch gear and other electrical parts, plastic dinnerware, radio and television cabinets, furniture drawers, buttons, knobs, handles, etc. Like the molding process itself, compression molding machinery is relatively simple. Most compression presses consist of two platens that close together, applying heat and pressure to the material inside a mold. The majority of the presses are hydraulically operated with plateau ranging in size from 6 in. square to 8 ft square or more. The platens exert pressures ranging from 6 up to 10,000 tons. Virtually all compression molding presses are of vertical design. Most presses having tonnages under 1000 are upward-acting, while most over 1,000 tons act downward. Some presses are built with a shuttleclamp arrangement that moves the mold out of the clamp section to facilitate setup and part removal. Compression molds can be divided into hand molds, semiautomatic molds, and automatic molds. The design of any of these molds must allow venting to provide for escape of steam, gas, or air produced during the operation. After the initial application of pressure the usual practice is to open the mold slightly to release the gases. This procedure is known as breathing. Hand molds are used primarily for experimental runs, for small production items, or for molding articles which, because of complexity of shape, require dismantling of mold sections to release them. Semiautomatic molds consist of units mounted firmly on the top and bottom platens of the press. The operation of the press closes and opens the mold and actuates the ejector system for removal of the molded article. However, an operator must load the molding material, actuate press controls for the molding sequence, and remove the ejected piece from the mold. This method is widely used. Fully automatic molds are specially designed for adaptation to a completely automatic press. The entire operation cycle, including loading and unloading of the mold, is performed automatically, and all molding operations are accurately controlled. Thermosetting polymers can be molded at rates up to 450 cycles/h. Tooling must be of the highest standard to meet the exacting demands of high-speed production. Automatic molds offer the most economical method for long production runs because labor costs are kept to a minimum. The three common types of mold designs are open flash, fully positive, and semipositive. |
|||
|